- 您现在的位置：买卖IC网 > Sheet目录349 > PCA9624PW,118 (NXP Semiconductors)IC LED DRIVER RGBA 24-TSSOP
NXP Semiconductors
PCA9624
8-bit Fm+ I 2 C-bus 100 mA 40 V LED driver
7.3.7 SUBADR1 to SUBADR3, I 2 C-bus subaddress 1 to 3
Table 11.
SUBADR1 to SUBADR3 - I 2 C-bus subaddress registers 0 to 3 (address 0Eh to
10h) bit description
Legend: * default value.
Address
Register
Bit
Symbol
Access Value
Description
0Eh
0Fh
10h
SUBADR1
SUBADR2
SUBADR3
7:1
0
7:1
0
7:1
0
A1[7:1]
A1[0]
A2[7:1]
A2[0]
A3[7:1]
A3[0]
R/W
R only
R/W
R only
R/W
R only
1110 001*
0*
1110 010*
0*
1110 100*
0*
I 2 C-bus subaddress 1
reserved
I 2 C-bus subaddress 2
reserved
I 2 C-bus subaddress 3
reserved
Subaddresses are programmable through the I 2 C-bus. Default power-up values are E2h,
E4h, E8h, and the device(s) will not acknowledge these addresses right after power-up
(the corresponding SUBx bit in MODE1 register is equal to 0).
Once subaddresses have been programmed to their right values, SUBx bits need to be
set to logic 1 in order to have the device acknowledging these addresses (MODE1
register).
Only the 7 MSBs representing the I 2 C-bus subaddress are valid. The LSB in SUBADRx
register is a read-only bit (0).
When SUBx is set to logic 1, the corresponding I 2 C-bus subaddress can be used during
either an I 2 C-bus read or write sequence.
7.3.8 ALLCALLADR, LED All Call I 2 C-bus address
Table 12.
ALLCALLADR - LED All Call I 2 C-bus address register (address 11h)
bit description
Legend: * default value.
Address
Register
Bit
Symbol
Access Value
Description
11h
ALLCALLADR
7:1
AC[7:1]
R/W
1110 000*
ALLCALL I 2 C-bus
address register
0
AC[0]
R only
0*
reserved
The LED All Call I 2 C-bus address allows all the PCA9624s on the bus to be programmed
at the same time (ALLCALL bit in register MODE1 must be equal to 1 (power-up default
state)). This address is programmable through the I 2 C-bus and can be used during either
an I 2 C-bus read or write sequence. The register address can also be programmed as a
Sub Call.
Only the 7 MSBs representing the All Call I 2 C-bus address are valid. The LSB in
ALLCALLADR register is a read-only bit (0).
If ALLCALL bit = 0, the device does not acknowledge the address programmed in register
ALLCALLADR.
PCA9624
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 3 — 6 September 2012
? NXP B.V. 2012. All rights reserved.
12 of 37
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
PCA9625D/S911,518
IC LED DRIVER RGBA 32-SOIC
PCA9626BS,518
IC LED DRIVER RGBA 48HVQFN
PCA9632DP2,118
IC LED DRIVER RGBA 10-TSSOP
PCA9633BS,118
IC LED DRIVER RGBA 16-HVQFN
PCA9634D,118
IC LED DRIVER RGBA 20-SOIC
PCA9635PW/S911,118
IC LED DRIVER RGBA 28-TSSOP
PCA9685PW,118
IC LED DRIVER RGBA 28-TSSOP
PCA9922PW,118
IC LED DRIVER LINEAR 16-TSSOP
相关代理商/技术参数
PCA9624PW112
制造商:NXP Semiconductors 功能描述:IC LED DRVR TSSOP
PCA9625D
功能描述:LED照明驱动器 16BT I2C FMTP LED HVCON RST OE RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9625D,512
功能描述:LED照明驱动器 16BT I2C FMTP LED HVCON RST OE RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9625D,518
功能描述:LED照明驱动器 16-bit Fm I2C Bus 100mA 24 V LED drivr RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9625D/S911,518
功能描述:LED照明驱动器 16BT I2C FMTP LED HVCON RST OE RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9625D/S911-T
功能描述:LED照明驱动器 16BT I2C FMTP LED HVCON RST OE RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9625DS911,518
功能描述:LED照明驱动器 16-bit Fm I2C Bus 100mA 24 V LED drivr RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N
PCA9625D-T
功能描述:LED照明驱动器 16BT I2C FMTP LED HVCON RST OE RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N